Hitachi CPX960WE Manuale Utente

HITACHILiquid Crystal ProjectorModelCP-X960W/EUSER'S GUIDE/Thank you for purchasing the Hitachi liquid crystal projector. Please read this user&a

Names and functions of each part (continued)Remote control transmitterVIDEO, RGB button _ _ LASER buttonPress to switch the input. (Refer to page 13,

Names and functions of each part (continued)fLoading the batteries Loading AA batteries into the remote control.[]Remove the batterycover.Push the kno

InstallationTypical LCD Projector and Screen InstallationUse the diagram below as reference to determine the screen size and projection distnace.Scree

Basic operationsTo project 11_5 7 4 2m5_j41 Turn on the main power switch of the projector [ I: ON].• The Power indicator lights orange.2Press the STA

Basic operations (continued)Turning off the power]21P _n P MUTEBLANK AUTO TIMER1Press the STANDBY/ON button for approximately 1 sec.• The Power indica

Basic operations (continued)[Freeze function]This function is used to freeze the image being displayed.(refer to page 10)p _nP MUTEC) @BkANK AUTO TIME

Basic operations (continued)I Magnify functionPart of an image can be displayed magnified.(refer to page 10)5S_p _np MUTEBL_NK AUTO TIMER1 Press the M

Adjustments and functions1,2,31\31Press the MENU ( _)_)(_(_ ) buttons of the projector or theMENU button of the remote control.• The Menu screen wilt

Adjustments and functions (continued)SET UPImages and display positions can be adjusted from the SETUP menu.RGB signal input Video signal input[ ETUP

Adjustments and functions (continued)INPUT 1The INPUT menu is used to select RGB signal sync signal frequency of the monitor and the VIDEO signal.I M

Adjustments and functions (continued)IMAGEProjection image inversion, etc., can be selected from the IMAGE menu._E5_P_ IN FL bSETUP INPUT IMAGE OPTSET

Adjustments and functions (continued)OPTCommunication functions, etc., can be set from the OPT menu.[SETUP[ _NPUTCOMSPEEDCOMBITSTIMERLANGUAGEAUTO OFFS

Connection to the video signal terminals1. Input signalsBrightness signalColor signalS-VIDEO signalVIDEO signalAudio signalInputOutput2. Signal input

ConnectiontotheRGBsignalterminal(continued)3. Example of computer signalResolution fH fVH x V (kHz) (Hz) Rating Signal mode Display mode Note 1640 x 4

ConnectiontotheRGBsignalterminal(continued)4. Initial set signalsThe following signals are used for the initial settings.The signal timing of some com

Connecting the USB1. Connect the projector and computer with a suitable commercially available cable.2. Press the 1NPUT button of the projector or the

Connection to the control signal terminal1. Mouse functions(1) Turn off the main power switches of the projector and computer and connect the two unit

Connectiontothecontrolsignalterminal(continued)CONTROL signal jackMousePin no. RS-232CPS/2 ADB Serial BUS1 YB2 CLK3 DATA DATA4 XA5 XB6 SELO SELO SELO

Connectiontothecontrolsignalterminal(continued)2. RS232C communication(1) Turn off the projector and computer power supplies and connect with the RS23

Connectiontothecontrolsignalterminal(continued)Command data chartItem Data codeMOUSE 00h=disable mouse function, 01 - 7Fh=start mouse functionCOMMUNIC

Before Use<Before Using>About the Symbols Various symbols are used in this instruction manual and on the product itself toensure correct usage,

Connectiontothecontrolsignalterminal(continued)Requesting projector status(1) Send the request code '20H' + 'yyH' from the compute

Example of system setupComputer(notebook type)Computer(desktop type)AC input@iiiiiiI/ \Video tape recorder with S jack/Video tape recorderSpeaker (wit

Cleaning the Air filter (continued)3 Cleaning the air filter with a vacuum cleaner4 Installing the air filter(Caution)When the air filter becomes clog

Message table (continued)IndicatorsThe POWER indicator, LAMP indicator and TEMP indicator light or blink in the following cases.POWERindicatorLights o

Specifi cations .Thesespeoi'_oationsaresobjecttochangewithoutno.ce.Product name Liquid crystal projectorModel CP-X960W/EDisplay method Three liqu

About the warranty and after-serviceAbout the warranty]A warranty is provided for this product. Fill in the necessary items and store in a safe place.

[Safety Precaution]• If a problem should occur.® If smoke or a strange odor arise, continueduse could result in fire or electrical shock. Insuch case,

• Handle the power cord with care.®Do not damage, cut, process orstrongly twist the power cord. Placingheavy objects on the power cord, heating orstro

• Do not sit or place heavy objects onthis projector.® Do not sit on this projector.AThis could result in overturning, _"_leading to damage or pe

• When the projector is not to be usedfor an extended period.For safety purposes when theprojector is not to be used for anextended period because of

Checking the package ContentsMake sure all of the following items are included in the package. If anything is missing, please contact yourdealer.Proje

Names and functions of each part (continued)Remote control photoreceptor/Main power switchUsed to turn the power on and off,© : OFFI:ONAC IN jack /Use